So you need to measure the resistance of the relay coil and figure out the current it needs (I = V/R). This means the coil will be powerful and take a lot of current - but I can't find any proper data for it. I am stupid.įirstly the RF6105-12V-C relay seems to be a high power contactor, switching 150A. The relay is controlling a 12v linear actuator. I want the relay to engage when the pin d1 goes high. The relay engages when I get 0v or ground going to the point that the "collector" is going to in the diagram. Did I wire them up correctly? Is my resistor too large/small? I assume the transistors went bad or I shorted them out when mounting it. I have confirmed that the relays are still good, but I can't get it to work with the transistors. ![]() I mounted the actuator and it stopped working. ![]() I was able to engage the linear actuator via 3.3v from wemos board - transistor - relay several times without any problems. I had two of the transistors with a 2.1K resistor switching two separate relays and it worked. I didn't have any TIP120's on hand, so yesterday I thought I would try the 2n2222 to do the exact same thing. I did this same exact thing on another project, but I used a TIP120 transistor with a 2.1K resistor and arduino uno to do the switching, and it is still in use now. I am trying to switch a rf6105-12v-c (what I am calling a relay?) with a 2n2222 transistor. New devices no longer come out as through-hole packages.I have read many threads about using transistors to switch relays of larger voltages on with microcontrollers, but most of them end without a solution, or I am not smart enough to understand the responses given. With the same pinout it would be a winner in the hobbyist market at least, but The ULN2803 is a chip with eight 0.5A darlington transistors sharing emitters,Ī handy device for switching multiple loads. Substantially higher load currents and lower Vsat. Or to put it in brief you don't necessarily need to go to a TO220 MOSFET orĭarlington for switching loads of an amp or two - for instance a stack of 8Į-Line superbeta transistors fits on the footprint of an ULN2803 and provides Which are super-beta in TO92 and e-Line packages respectively. ![]() In through-hole packages, for instance I've a few STX724's and ZTX851's Peak I've seen in a small transistor, 50mV Vsat at 1A. Newer "super-beta" devices (which are usually surface mount) perform loadsīetter than the average small signal transistor, for instance 5A max and 20A Have ratings like 30V to 80V, 0.15 to 0.5A. Maximum currents, order of 50mA, but they are rare and exotic and unlikely toĪ switching transistor is optimized for low Vsat and low stored-charge, but allīipolar transistors behave basically the same. And when I switched back to the Mosfet, the onboard LED once again blinked in sync with the LED on the breadboard.Ĭaveat - there are high voltage and high frequency transistors that have very low But when I removed the Transistor, the onboard LED started flashing again. It spooked me when I switched from the Mosfet to the Transistor because I thought I managed to blow out the onboard LED. (Using pin 13.) But when I use the Transistor to control the ON/OFF switching, the onboard LED is always off. When I use the Mosfet transistor to control the ON/OFF switching of the LED, the onboard LED flashes in sync with the LED on the breadboard. Any small-signal transistor is good for switching moderate levels of current in the range of a couple hundred milliamps.Īh ok. It's very cool to control physical things with a bit of simple code. After a few wiring mistakes, I was able to make it work for my sample project with these 4 LED's. Project 9 has an example for using the Mosfet transistor. Logic-level MOSFETs can be used, n-channel for low-side switching, (Which don't seem to ever get used by the included Projects.) That PDF says they are "Amplifier" transistors though, so I assume they cannot be used for ON/OFF switching? The Starter Kit I have came with 5 Transistor. Would switch on the low side (ground side). So a basic 5v relay isn't any good by itself?įor 4 LEDs a small switching transistor like the 2N2222 (NPN) would do, and So its best reserved for switching say mains or very high power circuits).Īh. (but the latter would need a BJT or MOSFET to power it and a free-wheel diode, You have a choice of BJT (bipolar junction transistor), MOSFET, or mechanical relay ![]() Each Arduino pin is powerful enough to control a single LED (20mA of current), butĪs currents get larger a switching device is needed.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |